Custom "Jailbreak" firmware for the Analogue Super Nt (regular and ghostly models) that allows loading ROMs from the SD Card slot and an expanded featureset.
Unzip snt_firmware_verJB7.0zip into the root directory of your SD card. Be sure that there is only one firmware file there. Insert the card into your Super Nt and power on. The firmware will be flashed to the console. This process may take a few minutes.
While the firmware is flashing the LED will turn red and flicker, followed by a considerable pause and HDMI signal blackout. Do not power off. The main menu will boot when it has finished. Delete the firmware file from your card after flashing.
The Super Nt is protected from bricking as a result of firmware updates, but please still follow the above precautions to be safe.
Create a folder called
SNES at the root of your SD card, and drop
your folders and subfolders of ROMs inside (see SmokeMonster's
for a curated list of valid SNES
The system will search for ROMs in the
/SNES/ folder first, or the
root directory of the SD card if there is no
/SNES/ folder. The
maximum number of files (ROMs and subfolders) that can be placed in a
given folder is around 300-500, depending on the length of the
Select browse SD card from the main menu. Hit enter on a filename to run it, or if it's a subfolder, it will enter said folder. The menu hotkey will return to the file menu from the game.
Saves will go into
/SAVES/SNES/ by default. You can directly place
an SD2SNES or Super
SD card in, and it will properly detect this by checking for the
requisite save game folders, in this order:
The Super Everdrive uses a 32-kilobyte long save file no matter what,
and is padded. This functionality is retained. It should be possible
to swap your SD card into the unit from your SD2SNES or Super
EverDrive and the saves will work fine, then it can be put back into
said cartridge and it will find the updated saves (with a
extension, other extensions are not recognized).
NEVER insert or remove cartridges while your Super Nt is powered on. Doing so may risk damaging the console and/or losing saves. It is good practice to backup saves before updating firmware.
When a game is exited to the menu, it will prompt you to save. Return to
the file menu and save your progress before powering down. NOTE: The
prompt to save is turned off by default, to enable it, open the menu
DOWN), then navigate to
MENU OPTIONS. Make sure
PROMPT WHEN SAVING RAM is selected.
CopySNES backs up (AKA "dumps") cartridge ROMs and save RAM to the SD card.
CopySNES is designed to be an easy to use way to back up cartridge ROMs and save RAM data. Most types of cartridges are supported, and if it isn't specifically supported or for some reason the cartridge header is bad, the settings can be changed.
How to use it:
CopySNESon the tools menu
At this point, CopySNES will query the cartridge and grab the header and attempt to detect what kind of cartridge it is.
You have two options at this point:
enterto accept the settings and proceed to saving.
startto edit the detected settings
(note: editing the name will happen during the save step, skip to
filename entry below)
If you wish to edit the settings, use
down to select one of
the settings, then use
right to adjust it. You can select
between 32 kilobytes and 16 megabytes of ROM to dump, and between 0
(i.e. none) and 32 kilobytes of RAM.
Finally, you can select the type of mapper it is, i.e. LOROM, HIROM,
EXHIROM, or EXLOROM. There is also a
FLAT setting which will let you
dump the entire SNES cartridge space if desired.
FLAT starts at
address 00:0000 and will dump the specified amount of memory.
While you can dump say, 8 megabytes of LOROM or HIROM, doing so most likely won't be very useful.
manual mode is useful when dumping things that do not have a
valid or any header such as the Game Genie BIOS (it reports 0 kilobyte
of ROM and is actually 64 kilobytes) or the Sufami Turbo (again, it
reports 0 kilobyte of ROM even though it's really 1 megabyte).
When you are done adjusting the settings, and are ready to dump, hit
At this point the filename can be edited. It will directly copy the
ROM header name in here. For some Japanese titles, there may be no
valid ASCII characters in the header (or if there's no header at all)
so any invalid characters for a filename are replaced with spaces. If
there's no name at all, it will default to "GAME". Use
change the character's value and
right to select a
enter to accept the filename and begin the dumping
The game's actual size will be determined at this point (i.e. a 2-megabyte game reported in the header might only be 1.5 megabytes, so this will be detected now).
Finally, the ROM and RAM are dumped to the SD card.
Now that the dump is complete, you are returned to the tools menu. The system can be powered off and a new cartridge inserted to dump, and so on until all the carts are dumped that you wish to dump.
The following things have been tested:
(note: for SuperFX (GSU), the RAM is always dumped as 64 kilobytes. This is because games such as Yoshi's Island have RAM, but the headers for all the games show 0 kilobyte of RAM. This 'larger' RAM will work with the major emulators, and can be trimmed down later if needed.)
Note: Testing with
no$sns it will not use the saves on certain games
such as Chrono Trigger I don't know why, the saves are good and work
on the Super NT itself.
Since Super NT firmware version JB6.9, the System -> Font menu allows you to select your own font in place of those which come with the console. The load font option will bring you to the file browser. If you have a directory called
/FONT/ at the root of your SD card, it will default to that directory to load a font file. The font must use an 8x8 text box and must be represented in binary in a 1-bit per pixel format. Each character will take eight bytes to represent in this format. The file must be 768 or 1024 bytes in size and use the extension .fnt. The characters in the file will have to start at ASCII 20 (space) and end at ASCII 7F (delete). Font files 1024 bytes in size will not show the first 32 characters which would be stored in the first 256 bytes of that file. A set of user-created fonts compiled by Sho is available here. Utilities to convert Analogue font files to/from bitmap files are available here.
Cheat codesis moved into the file browser settings menu.
/COPYSNES/. The directory is created if it does not exist. See the text file for full instructions.
toolsmenu appears on the main menu which has CopySNES and cheat codes.
menu bounceoption (reinstated)
return to menushortcut
JB6.4 2018-02-14 Initial release: Happy Valentine's Day ❤️
The custom firmware is not coded by SmokeMonsterPacks or frederic-mahe, but please do report problems here at Github for support. Priority will be given to jailbreak-specific problems (using ROMs through the SD card slot rather than through the cartridge slot). You can join the discord server if you want to chat with the Super Nt community.
Use at your own discretion. We are not responsible for any damage or data loss caused by custom firmware installation or use.