BitTorrent Protocol Daemon
btpd is a utility for sharing files over the BitTorrent network protocol.
It runs in daemon mode, thus needing no controlling terminal or gui.
Instead, the daemon is controlled by btcli, its command line utility,
or other programs capable of sending commands and queries on the control
btpd consists of the following programs:
btpd- The bittorrent client.
btcli- Command line interface to btpd.
btinfo- Shows information from a torrent file.
All programs accept the
btcli utility has several different modes of operation. One of the following commands must be specified when running
add- Add torrents to btpd.
del- Remove torrents from btpd.
kill- Shut down btpd.
list- List torrents.
rate- Set the global up and download rates in KB/s.
start- Activate torrents.
stat- Display stats for active torrents.
stop- Deactivate torrents.
To start sharing a torrent with btpd, the torrent needs to be added to
btpd. This is done with
btcli add. When you add a torrent btpd automatically (if you didn't specify otherwise) starts to share the torrent
and download any missing data. The content directory you specify when
adding a torrent doesn't need to exist; it will be created by btpd.
You can see which torrents have been added to btpd with
The list command also displays a number for each added torrent. This number
can be used to specify the target torrent for the btcli commands, so you
don't have to keep the torrent file once you've added it.
The up- and download progress can be followed by using the
command. Both the list and stat commands use the following indicators to
display the state of a torrent:
+- the torrent is starting. This may take time if btpd needs to test the content of this torrent or one started before it.
-- the torrent is being stopped.
I- the torrent is inactive.
S- btpd is seeding the torrent.
L- btpd is leeching the torrent.
You can stop an active torrent with
btcli stop and, of course,
start an inactive torrent by using
btcli del command should only be used when you're totally finished
with sharing a torrent. The command will remove the torrent and its
associated data from btpd. It's an escpecially bad idea to remove a not
fully downloaded torrent and then adding it again, since btpd has lost
information on the not fully downloaded pieces and will need to download
the data again.
To shut down btpd use
btcli kill. Don't forget to read the help for each
of btcli's commands.
NOTE: You should only need one instance of btpd regardless of how many torrents you want to share.
To start btpd with default settings you only need to run it. However,
there are many useful options you may want to use. To see a full list
btpd --help. If you didn't specify otherwise, btpd starts with
the same set of active torrents as it had the last time it was shut down.
btdp will store information and write its log in
it needs to be able to write there during its execution. You can specify
another directory via the
-d option or the
I recommend specifiying the maximum number of uploads. Bittorrent employs a tit for tat algorithm, so uploading at good rates allows for downloading. Try to find a balance between uploads/outgoing bandwidth and the number of active torrents.
Start btpd with all options set to their default values.
Start btpd and make it listen on port 12345, limit outgoing bandwidth to 200kB/s, limit the number of peers to 40 and not start any torrents that were active the last time btpd was shut down.
# btpd -p 12345 --bw-out 200 --max-peers 40 --empty-start
Display a list btpd's torrents and their number, size, status, etc.
# btcli list
Same as above, but only for torrent 12 and my.little.torrent.
# btcli list 12 my.little.torrent
Same as above but only for active torrents.
# btcli list -a
Same as above, but print using a custom format
# btcli list -a -f "btcli list -f "%n\t%#\t%p%s\t%r\n"
Add foo.torrent, with content dir foo.torrent.d, and start it.
# btcli add -d foo.torrent.d foo.torrent
Same as above without starting it.
# btcli add --no-start -d foo.torrent.d foo.torrent
Start bar.torrent and torrent number 7.
# btcli start bar.torrent 7
Stop torrent number 7.
# btcli stop 7
Stop all active torrents.
# btcli stop -a
Remove bar.torrent and it's associated information from btpd.
# btcli del bar.torrent
Display a summary of up/download stats for the active torrents.
# btcli stat
Display the summary once every five seconds.
# btcli stat -w 5
Same as above, but also display individual stats for each active torrent.
# btcli stat -w 5 -i
Set the global upload rate to 20KB/s and download rate to 1MB/s.
# btcli rate 20K 1M
Shut down btpd.
# btcli kill
If btpd has shut down for some unknown reason, check the logfile for possible clues.
You should have a BSD, Linux or sufficiently similar system.
Make sure you have recent versions of the following software:
You also need a c99 compiler. A non antique GCC should do.
To be able to open the manual located in
doc you need to have
# ./configure # make # make install
./configure --help for available build options if the above fails.
The layout of the torrents directory in the btpd directory has changed since btpd 0.11. Please remove the torrents directory before running later versions.
If btpd needs to send stop messages to trackers before shutting down, it will enter the pre exit mode. A btpd process in this mode can safely be ignored and will not interfere with any new btpd started in the same directory.
Unfortunately enabling both IPv6 and IPv4 in btpd is less useful than it should be. The problem is that some sites have trackers for both versions and it's likely that the IPv6 one, which probably has less peers, will be used in favour of the IPv4 one.
In order to fix this problem, the IP version options should be changed to be per torrent, in some future version of btpd.
If you wish to get in touch to get help, contribute or just say hi, don't hesitate to come to our IRC channel #btpd on freenode.